how to remove push lock fuel line without tool

Pull the spring lock coupling fittings apart. Do not use metal tools to remove the O-ring seals.

Subaru Fuel Line Removal No Special Tools Youtube

Fuel Line Removal Tool.

. For many modern hose connections a hose clamp is a thing of the past. Plumbing Solutions Shop Tips. Plumbing a fuel system what you need checking fuel pipes how a car works remove push lock fuel line without tool checking fuel pipes how a car works fuel line disconnect chevrolet forum. Remove push-lock hose with a soldering iron.

How To Remove Plastic Fuel Line Connectors. How to assemble Push-Lok hose quicker and easier. Thats right instead of using a knife to do the job take a soldering gun and put a plastic cutting tip on it. Scissor Fuel Line Disconnect Tool for 38 inch and 516inch Easy Separation of Quick Disconnect Style Fittings use on Fuel Heater and AC Line Service Compatible with.

Using a knife or razor blade to remove the hose could damage the barb on the fitting and lead to a leak. Push the hose over the first barb to get it started. They can cause axial scratches across the O-ring seal grooves resulting in refrigerant leaks. Replace the line with factory version.

This is a video of me replacing the fuel filter on my 1999 Ford Ranger. An easy way to disconnect the Ford fuel line fittings without using a tool. The EZ-ON Hose Press is so simple to use it almost makes installing push lock hose fun. Go to Napa they sell a quick disconnect kit with 4 different sizes you want the gray one.

Tip for Installing Braided Stainless Steel Hose to the Threads of. Use an alternate fuel hose with the existing fittings clamp on with hose clamps. China Plastic Pipe Quick Connector Mct7 89 Id6 180 21 For Auto Parts Fuel Liquid System Photos Pictures Made In. You slip it on the gas line push it up to the connector and it releases the lock and it slides right off.

How to Remove Push Lock Hose without Damaging the Fitting. The OEMTOOLS Fuel Line Disconnect Tool features a scissor-like design that allows for easy damage-free fuel line quick disconnect coupler release. To use this tool set just select the piece that fits your hose or pipe. Tool box that are going to depress the little latching tabs that are on the fuel line.

Here are the steps. We have done thousands of these type assemblies and the very best way to do it is with a pot of boiling water. Next bend it 90 degrees so it acts like a cutting blade. Remove the AC tube lock coupling spring with a.

Clamp the hose into the travelling carriage. Id like to reuse the fitting and line since I only had to remove about 10mm of old line where the break was. Get Baum tool heat line in water and tap on. Secure the fitting in the stationary vise.

Here is a video showing how these work. Fitting Fixer repairs scratches dings imperfections and other. While holding pressure on the line with a small screwdriver I used a 18 blade run the screwdriver underneath the spring and slowly go around. The ToolPRO AC and Fuel Line Disconnect set is what youll need for modern push lock connections.

Just dip the hose into the water for 20 seconds or so use a shop. The kit cost like 200. Brand new to the industry is Fitting Fixeran inverted 37 cone thats coated with diamond dust. DO NOT use any kind of lubricant to assemble the hose onto the fitting.

The ability to repair leaky fittings that are attached or welded to a tank is invaluable. I was able to make a tool to overcome the quick disconnect fitting couplers out of an. Use the same tool to replace the fuel filter. Use an impact gun or ratchet with a 17mm socket to drive the hose onto the barb.

You need a FUEL LINE REMOVAL TOOL that slips over the line pushes the tabs holding the line OUT and then allows you to remove the connector. Simply place the tool around the fuel line and push into the female connector to release the male connector. The key is only put SLIGHT pressure. While holding the fuel that pulls out of the fitting put slight pressure in the OUT direction like youre trying to disconnect the fitting.

These connectors feature a locking tab inside the fitting where using your fingers or a screwdriver is not possible. A general guide for disconnecting the most common setup of fuel lines from a fuel pump. Slip the opening in the tool over the hose or pipe. Remove the O-ring seals with a non-metallic tool.

Push Lock Hose Installation Tool. You can find these tools at any auto parts store your. Fuel Filter Disconnect Tool - GM Fits GM flex fuel systemsDisconnects the fuel line from the fuel filter on 53L Suburban Tahoe Yukon Avalanche and select Silverados and SierrasInsert the two semicircular disconnects into the couplingConnect the handle and depress to separate the fuel line from the filterShipping weight 2 oz. How to Install Braided Stainless Hose into AN Fittings.

May 29 2021 How To Remove Push Lock Fuel Line Without Tool First push the whole connector forwards then pull the green in case quick connector tab.

Diy Removing A Push Lock Fuel Line Fitting Youtube